Skip to contentHydramill Tools

Epoxy resin calculator (volume and mix ratio)

How much epoxy resin you need for a mould, tray, coaster or table: volume from size and depth, extra margin, and the amounts of part A and part B in ml, litres, fl oz and grams.

Mould shape
Unit
Mix ratio by volume (A:B)

Result

Mould volume600 ml (0.6 L, 20.3 fl oz)
Resin needed (with margin)660 ml (0.66 L, 22.3 fl oz)
Part A (resin)330 ml (0.33 L, 11.2 fl oz)
Part B (hardener)330 ml (0.33 L, 11.2 fl oz)
Total weight726 g (25.6 oz)
Part A weight363 g (12.8 oz)
Part B weight363 g (12.8 oz)

Approximate: weights assume the same density for both parts. Always follow the ratio and the measuring method (by volume or by weight) on your resin's label.

How the resin amount is worked out

The mould volume is length x width x depth (or pi x radius squared x depth for a round mould); 1 cm3 is 1 ml and 1 in3 is 16.387 ml. The margin adds extra for spills and uneven surfaces, and the total is split by the mix ratio by volume, e.g. 2:1 is two parts A to one part B. Weights multiply the volume by one density; check your brand's data sheet, since resins differ.

How to use it

  1. Choose the Mould shape, Rectangle or Round, and the Unit (centimetres or inches). Enter Length and Width, or the Diameter for a round mould, and the Depth you will pour.
  2. Pick the Mix ratio by volume (A:B) from your resin's label: 1:1, 2:1 or Custom with your own numbers.
  3. Set the Extra margin, 10 % by default, to cover spills, the film left in the cup and uneven surfaces. Increase it for textured moulds.
  4. Optionally adjust the Resin density from the data sheet. Read the Result: mould volume, resin needed with margin, Part A and Part B in ml, litres and fluid ounces, and the approximate weights.

Worked example

A rectangular tray 30 cm long, 20 cm wide and 1 cm deep holds 30 x 20 x 1 = 600 ml. With the default 10 % margin you need 660 ml of mixed resin. At a 1:1 ratio that is 330 ml of Part A and 330 ml of Part B. At a 2:1 ratio it is 440 ml of A and 220 ml of B. With the default density of 1.1 g/ml the total weighs about 726 g. A round coaster 10 cm across and 1 cm deep holds pi x 5 x 5 x 1 = 78.5 ml before the margin.

Frequently asked questions

Should I measure epoxy by volume or by weight?

Do what the label says, because the ratio is defined one way or the other. Many casting resins are 1:1 by volume, but by weight the same product can be a different ratio because parts A and B have different densities. This tool splits by volume and gives weights as an approximation only, so do not weigh parts from it unless the data sheet gives a weight ratio.

Why add a margin to the resin amount?

Some resin always stays on the cup, stirrer and mould walls, and the surface is rarely perfectly level or the mould perfectly sized. A 10 % margin is a sensible start for a smooth mould and more is wise for textured or irregular ones. Leftover mixed resin can be poured into a spare mould.

How deep can I pour in one go?

It depends on the product. Casting and deep-pour resins are made for thick layers, while standard coating resins are meant for thin layers of a few millimetres, and a thick pour can overheat and cure unevenly. Check the maximum pour depth on the data sheet, and pour in layers if needed, working out each layer separately here.

How accurate is the weight?

It is approximate. The tool multiplies volume by a single density, 1.1 g/ml by default, for both parts. Real resins differ and so do hardeners. Weigh a known volume of your own resin and enter that density if you need better numbers.

What safety basics apply when mixing resin?

Wear nitrile gloves and eye protection, work in a ventilated room and avoid skin contact with uncured resin. Mix for the time on the label and scrape the sides, since poorly mixed resin stays tacky. Follow the manufacturer's safety data sheet.

Everything is calculated in your browser: this site doesn't send what you type anywhere.